Oil Filter Kits

How to order

Carriage on all oil filter kits to UK £4.25

Click Here for a dimensioned drawing of the filter assembly

 

Unlike most car engines, classic bikes suffer from very poor oil filtration, leading to comparatively rapid wear of the major engine components. Gauze and/or felt filters will trap larger debris but allow smaller particles, down to micron size, to circulate causing continual wear. Modern detergent oils are designed to carry particles along to be effectively filtered out. Fitting an up to date replaceable cartridge filter will give an older motorcycle modern filtration levels allowing much greater engine life.

Now available as a kit, this filter system comes tailor made to suit each individual model allowing easy fitting. Everything required for installation is included in each kit along with full step by step instructions. The Cartridge is a 2CV Citroen equivalent. This is a proven modification with many hundreds of kits sold over more than 20 years.

BSA A50/65 pre-oif kit shown above, mounts behind the gearbox on a stainless bracket. Fastners hose and hose clips supplied. PT. no. OFKA65

BSA A65 oif mounts above the nearside of the gearbox, with stainless bracket hose clips and fastners. PT.no.OFKA65OIF

BSA B25/44 mounts behind the gearbox on a stainless bracket. Fastners hose and hose clips supplied. Pt.no.OFKB25

BSA B50 mounts behind the gearbox on a stainless bracket. Fastners hose and hose clips supplied. Presumably this will also fit the Adventurer, but there isn't one locally to check. Pt.no.OFKB50

BSA A7/Al0 S/Arm kit mounts out of sight in the toolbox, and includes everything needed to protect that bush, St./St. fastners, fittings, hose,and hose clips. Pt.no. OFKA10

NORTON FEATHERBED kit mounts the filter behind the gearbox on a St./St. bracket & is supplied with 1.0M. of hose and stainless hose clips enabling most engine/oiltank combinations to be covered. Pt.no. OFKFB

TRIUMPH 650/750 oil in frame mounts above the nearside of the gearbox, with stainless bracket hose clips and fastners. Pt. no. OFKTRIOIF

TRIUMPH 650 pre oil in frame mounts behind the gearbox and comes with everything needed for installation. Pt.no.OFKTRIPREOIF

TRIUMPH 350/500 unit mounts out of sight below the gearbox. Pt.no. OFKTRI350

TRIUMPH 500/650 Pre unit mounts behind the gearbox and comes with everything needed for installation. Pt.no.OFKTRIPUNIT

UNIVERSAL comes with 1.0m of hose, stainless fastners, hose clips, grommets for panel mounting, and a pre drilled St./St. mounting bracket that can be adapted to fit most bikes. Pt.no. OFKUNIV

"The instructions were clear .... it was exceptionally easy to fit", Steve Wilson, Classic Bike Guide April 1999

All filter kits £46.00 + £4.25 P&P

Replacement cartridges £4.95 + £2.50 P&P Pt.no. OILCART0
 

The filter mounting head is available by itself for £19.85

Pt.no. OFKMH

The filter uses a 16mm X 1.5mm pitch thread .

The mounting holes are 5/16" UNF

 

Filters for 1/4" (6MM) petrol hose approx. 1" dia.

Pt.no.PT FFTCL £2.00 each

Plated brass ferrules for 1/4" bore 'rubber' petrol line. These can be crimped if you have the proper tool, but when used with the black 'rubber' hose below give a tight seal when simply pushed on.

Pt. no. PT73021

0.75P ea

Available in 1/4", 5/16" and 3/8" bore, this hose is suitable for petrol or hot engine oil at up to 16.5 Bar. Sold in 1.0 Metre lengths. Proof against Super unleaded with methanol additive.

1/4"Pt.no.OILH014 £3.50

5/16" Pt.no. OILH516 £4.00

3/8" Pt.no. OILH038 £4.50 Not suitable for petrol

St./St. Jubilee type hose clips in sizes to suit

1/4" jubilee type clips to suit £1.00 Pt.no. OILJUB014

5/16" jubilee type clips to suit £1.00 Pt.no. OILJUB516

3/8" jubilee type clips to suit £1.00 Pt.no. OILJUB038

St./St 'O' clips in sizes to suit. These can be crimped with the proper tool, in the vice or using a pair of cutters, state the size.

1/4" O clips Pt.no.OILO014 £1.00

5/16" O clips Pt.no.OILO516 £1.00

1/4" O clips Pt.no.OILO038 £1.00

BSA A10 MAGNETIC SUMP PLATE & ST./ST. STRAINER KIT

 

BSA sump plate kit comprising a cast & machined aluminium housing, a magnetic sump plug, St./St. gauze strainer, gaskets & St./St. caphead screws & washers.

This is a very good addition to the lubrication system of the BSA twins using a magnet to attract microscopic ferrous particles that otherwise circulate in the oil causing wear.

We have made this as a finned aluminium casting as the rough surface & the fins helps to cool the oil as it passes.

The addition of a sump plug means that the sump can be easily & quickly drained after the bike has been left for some time & the oil has drained into the sump

£39.95 Pt.no. A10SPK

The parts are available seperately:

Finned ally. sump plate Pt.no. A1061221 £27.95 Also for B31/33,M20/21 Pt.no.B33616220 £27.95

St./St. sumplate filter for BSA A7/10, A50/65 Pt.no. A1097058 £8.95

 

 

 

 

What's new page
How to order
LED running lights for older cars/motorbikes
LED bulb replacements for cars & motorcycles
Brighter Quartz Halogen bulbs for older vehicles
Brighter headlamp bulbs for modern vehicles
Standard replacement bulbs, cars & m/cycles
Motorcycle indicators
Motorcycle batteries
Motorcycle & Car lighting
Motorcycle electrics
Pazon electronic ignitions & Mag. replacements
Alton generators, dynamo replacements
Motorcycle accessories
Motorcycle petrol taps and fittings
Motorcycle Oil Filter Kits
Speedos, tachos, drive units, mountings etc.
Handlebar levers for Classic Bikes
Girling Replica motorcycle shock absorbers
BSA fork upgrade kit & other A7/10 parts
Stainless Steel Silencer Clamps
Goffys Norbsa 850
Goffys A10
Homepage

 


P.R.Goff 62 Clare Rd. Prestwood Bucks. HP16 0NU

Telephone: 01494 868218 or mail me here Goffy

For enquiries/order details, please go to Order Page